约 110 个结果
在新选项卡中打开链接
  1. Kia Forum
    https://www.kia-forums.com › threads

    broken shift cable? | Kia Forum

  2. hondasxs.com
    https://hondasxs.com › threads

    P1000 1000-5 won’t get out of low gear - hondasxs.com

  3. Chrysler 300M Enthusiasts Club
    https://300mclub.org › forums › viewtopic.php

    Transmission shifter cable replacement - Chrysler 300M …

  4. smwebhead.com
    https://www.smwebhead.com › viewtopic.php

    Shift cable replacement on 2005 230 (240 in later years)

  5. harleytechtalk.com
    https://harleytechtalk.com › htt › index.php

    Detailed instructions to replace the shifter return spring needed.

  6. Sheldon Brown
    https://sheldonbrown.com › sturmey-archer › cable.html

    Installing Sturmey-Archer Gear Shift Cables - Sheldon Brown

  7. 其他用户还问了以下问题
    How do you replace a transmission cable?
    Push the transmission cable off of the shift selector, and with pliers pull upward to remove the retaining clip from the cable bracket. Tie a long string on the end of the old transmission cable, before you pull it out. The string will help pull the replacement back in, and identifies the route.

    Transmission shifter cable replacement - Chrysler 300M Enthusiasts Club

    300mclub.org
    Are there 105 di2 or GRX rim brake shifters?
    There are no 105 Di2 or GRX rim brake shifters. You can still build a budget-friendly 105 Di2 or GRX rim brake bike - but you’ll have to use one of these shifters: Dura-Ace ST-R9250 rim brake shifter. These shifters are essentially the 11-speed models, with SD300 ports and updated firmware.

    Building a 12-Speed Di2 Road/Gravel Bike - BetterShifting

    bettershifting.com
    How do you wire a GRX shifter?
    The second method of connecting wired shift levers involves a four-port junction, the EW-JC304. This is also how you’d wire up GRX, Ultegra and Dura-Ace wireless shifters. Each shifter is connected to the JC304 junction using a single EW-SD300 wire, and then a third wire runs from the JC304 junction to the battery.

    Building a 12-Speed Di2 Road/Gravel Bike - BetterShifting

    bettershifting.com
    How many wires do you need to connect a shift lever?
    At the bare minimum, you’ll need two wires. One to connect the front derailleur to the battery, and one to connect the rear derailleur to the battery. In this setup, the shift levers operate wirelessly.

    Building a 12-Speed Di2 Road/Gravel Bike - BetterShifting

    bettershifting.com
    Should I update my shifters?
    Updating the shifters can be especially troublesome if you’ve installed all components to the bike - they need to be wired to the system in order to be updated. This is also the time you confirm every component and wire actually works. Better now than later, after you’ve installed everything on the bike.

    Building a 12-Speed Di2 Road/Gravel Bike - BetterShifting

    bettershifting.com
    How do you wire a 12-speed rim brake shifter?
    This first method involves running an EW-SD300 wire from one shifter to the other, and then running a single wire from either shift lever to the third port on the battery. While the disc shifters only have one SD300 port, the 12-speed rim brake shifters have two SD300-type ports and one satellite shifter port.

    Building a 12-Speed Di2 Road/Gravel Bike - BetterShifting

    bettershifting.com
    反馈
  8. BetterShifting
    https://bettershifting.com

    Building a 12-Speed Di2 Road/Gravel Bike - components and wiring

  9. Rumble
    https://rumble.com

    Toyota Sienna - Broken Gear Shift Cable Bushing and …

    2025年1月17日 · 2006 Toyota Sienna transmission shift cable kit allows you to quickly and easily repair your shift selector cable by replacing the bushing. This kit allows you to repair the interior end of the cable which is located inside the …

  10. kia-forums.com
    https://www.kia-forums.com › threads › latest

    Shift cable broken?? | Kia Forum

  11. harleytechtalk.com
    https://harleytechtalk.com › htt › index.php

    Shifter Pawl Sleeve Question - harleytechtalk.com

  12. 某些结果已被删除