How to Remove and Install a Water Pump | Charger Forums
2010年12月10日 · Fig. Remove bolts (2 and 3) attaching water pump (1) to block-2.7L engine 11. Remove bolts attaching water pump to block. 12. Remove water pump and gasket. To install 1. Clean all sealing surfaces. 2. Install water pump and gasket. Tighten mounting bolts to 105 inch lbs. (12 Nm). 3. Install the timing chain guides and timing chain. 4.
3.5L water pump replacement how to - Charger Forums
2013年11月20日 · Recently I performed the timing belt and water pump replacement with a kit from AutoZone. After 3 months the pump started leaking at the shaft. Here is my how to replace the water pump without removing the crank pulley. Remove the serp belt and tensioner and make your way down to the timing belt as shown in the how to replace your timing belt ...
3.5 water pump replacement - Charger Forums
2009年1月26日 · Can anyone give advice on how to remove the tensioner? Once I get this off, I can remove the timing belt then remove the water pump. FYI: I found a replacement waterpump at Autozone for $57.99 (dodge wanted $100.15) Timing belt from Autozone $45.99 (dodge wanted $169.10) and a new timing belt tensioner from Autozone $34.99 (dodge wanted $147.40).
water pump replacement 6.1 - Charger Forums
2009年6月9日 · What I did is got the new water pump, and everybolt I took off i put it on the new waterpump so I would know where they are to go when installing. I replaced my water pump in about 2 hrs. Charger SRT8 24"x 10"s, lambo doors, k&n cai, magnaflow exhuast, hid headlight & fogs, tinted tails, led interiors, viper 5900 remote start, 22elite leather ...
Belt guide pulley, tensioner, water pump | Charger Forums
2012年8月18日 · thanks for the link. Looks like the better procedure to replace the water pump is to: 1. Drain/flush system (Of course this means clearing out the air intake hoses etc to get easy access to stuff). 2. Remove serp belt. I've replaced the belt several times (I do have 212,000 miles on my car .. :driving: ) so I know how to do that easy thing. 3.
STILL RUNNING HOT AFTER CHANGING WATER PUMP AND …
2021年11月8日 · I have a 2018 Scat Pack. My car was running hot so I replaced the water pump and installed a 180 degree thermostat. the car ran well for a couple of weeks and then all of a sudden started running hot again.
The dreaded water pump failure strikes | Charger Forums
2023年11月15日 · 2014 Billet Silver Dodge Charger R/T AWD 10/27/16 2020 Destroyer Gray Durango SXT Plus AWD 2/24/23
08 Dodge Charger 2.7 V6 No Start After Timing Chain Replacement
2023年5月7日 · Replaced Water pump, Timing chain, tensioner, and cam shaft sprockets. After putting it back together it doesn’t start It turns over and you can see the crankshaft and cam shafts turn but freely with no compression. I’ll attach a link below to a video of what it looks and sounds like when I turn it over.
Help Needed!! Water Pump 5.7L - Charger Forums
2016年1月18日 · Note the location of the waterpump mounting bolts (2).6. Remove water pump mounting bolts (2) andremove water pump (1). Installation 5.7L/6.1L ENGINE1. Install water pump and mounting bolts (2). Tightenmounting bolts to 28 N·m (20 ft. lbs.).2. Make sure double ended bolt (3) is in the properlocation.
2007 2.7 timing chain hitting timing after replacement - Charger …
2021年8月8日 · Which is very common. On the "revised" water pump and gasket, they use a super thin coated gasket and revised the water pump for it by thickening up the water pump bolt flange where the two large bolts go through it. What this does is open a can of worms for mismatched parts. 1) you have to make sure the water pump matches the timing chain.