Anybody know where to get this 9 ply baltic birch (picture)?
2022年6月8日 · To get the 9 ply in Baltic birch it would need to be 1/2 thick. The 3/4 would have 13 plies. What you show is likely poplar plywood, it’s good for cabinet frames and panels and has 9 plies in the 3/4 inch thickness.
Plywood: 5 ply vs. 11 ply - FineWoodworking
2007年9月5日 · The quality of the veneer core plies is more important than the quantity . 5 ply domestic hardwood is the bottom of the line in most cases hardwood plywood 3/4" comes 7 and often 9 ply . The 11 ply or 17 ply is surely an overseas ( China probably ) product .
13-ply birch and oak plywood at Lowe's - FineWoodworking
2008年3月16日 · The norm here in Oregon is a 7 ply 3/4" , now and then we used to get 9 ply . I buy a much better then paint grade 7 ply panel for about $45 some times armour core for the same money . The China ply retails here for $30 - $35 a sheet .So a savings of $15 per sheet is the moment of truth in the real world .
plywood drawer question - FineWoodworking
2006年7月12日 · The Apple ply and Baltic Fin ply can be 7 - 9 ply so it leaves little room for voids to be . I putty the entire top side of the drawer parts then sand smooth basically removing any saw marks . Some may be rounded both in and out on the sides , are usually done before assembly with either a full 1/2 round or a bull nose router bit run on each side .
plywood for cabinets - FineWoodworking
2020年12月10日 · I’m building some shelving cabinets for the basement, and have lately experienced “sanded BC” plywood and “poplar” plywood (both 3/4″, both Low’s). The poplar is labeled “blondewood”, and is technically 9-ply but the outer plys/plies are so super thin that I’m not sure you can call them plies . The sanded BC is 5 ply.
Bending ply wood - FineWoodworking
2004年5月30日 · The spring back figures I suggested are purely random because the spring back is affected by several factors, e.g., thickness of the laminated parts, tightness of bend or bends, grain orientation of the laminated parts in relation to the bend orientation-- plywood bends more easily in one direction than the other, but this also affects the ...
Edge bands for 3/4 ply - FineWoodworking
2004年6月25日 · Looking for different techniques of edge banding 3/4 plywood. Have a couple of computer desk to make. Will be using 3/4 plywood ( maple) for the tops, and maple lumber for face frames, and panel doors. I have seen Burgess two piece router bits that look simple to use ( a bit pricy). Anyone have any thoughts on this subject. Thanks Pete
solid core plywood vs. 7-layer plywood - FineWoodworking
2002年6月12日 · What I'm really inquiring about is "lumber core" as described in John's response. I recently used a product that was briefly stocked at my local Home Depot. It was hardwood 1x3 strips with a mahogony veneer. It was light and easy to handle. I didn't see any disadvantages over traditional multi-ply laminated plywood.
Warped Birch ply - FineWoodworking
2008年4月28日 · Lowes sometimes has ApplePly rejects as hobby sheets in the 2-ft X 4-ft stuff, but it is hit or miss. They buy the hobby sheets from Columbia, and sometimes it is 9-ply, and others it is 5-ply. Sometimes plywood will warp with changes in moisture if one surface is exposed to air, and the other tight on the stack below it.
2-ply plywood: how much of a no-no? - FineWoodworking
2021年12月11日 · The box is almost 200 wide and 600mm long. The grain is in the same direction as the box. It’s probably functional as a single ply, however i’m imagining some rough treatment - when the box is full, dropped onto something hard, I can see it breaking easily.