The STLINK-V3MINIE tiny probe is a standalone debugging and programming probe for STM32 microcontrollers: • It supports JTAG and SWD protocols to communicate with any STM32 microcontroller. • It provides a Virtual COM port interface allowing the host PC to communicate with the target microcontroller

To use the built-in debugger, you must remove the jumpers from CN2 (Nucleo-64) or CN4 (Nucleo-144). Then you can use CN4 (Nucleo-64) or CN6 (Nucleo-144) to connect to your target board. This debugger has a 6-pin dupont header for connecting to a …

2016年11月20日 · 如果对外界编程，只需要从CN2卸下两个跳线，如图7，并根据表1将应用程序连接到CN4调试接口，就可以了。注：如果在外部应用程序你使用CN4的引脚5，SB12 NRST（目标MCU RESET）必须关闭。8 r9 `* T( n; B ( |! N3 c& u8 i% [" V) r' e7 i* u9 r6 g; X

2016年11月20日 · 如果对外界编程，只需要从CN2卸下两个跳线，如图7， 并根据表1将应用程序连接到CN4调试接口，就可以了。 注： 如果在外部应用程序你使用CN4的引脚5，SB12 NRST（目标MCU RESET）必须关闭。 实践中，一般只接1、2、3、4脚。 如果不接1、3脚，会对目标MCU板的电源造成很剧烈的干扰。 下面就是我经常用的板载 ST-LINK。 ，是不是很简单呢？ 如果对你有些帮助，请回帖留言哦~~~~~~~~~~~~~~~~ 楼主居然把板子掰断了，看着就觉得 …

2022年12月4日 · 思路比较简单， stlink子板上的CN4口是6pin swd输入口， 用来引入外部swd调试器的调试信号(根据原理图，似乎也可以连接外部swd平台，用子板st-link调试外部平台，这样来看，这个坐子既能输入也能输出调试信号）．主机环境运行openOCD和 gdb,完成对目标nucleo板的 …

The ST-LINK/V2 built into the Nucleo-64 and Nucleo-144 boards can also be used as stand-alone debugger. To use the built-in debugger, you must remove the jumpers from CN2 (Nucleo-64) or CN4 (Nucleo-144). Then you can use CN4 (Nucleo-64) or …

STLINK-V3MINIE is a portable version easy‑to‑use debugger and programmer including STDC14 interface with its flat cable

The ST-LINK/V2 programming and debugging tool is integrated on the STM32F072 Discovery kit. The embedded ST-LINK/V2 can be used in 2 different ways according to the jumper states (see Table 4): • Program/debug the MCU on board • Program/debug an MCU in an external application board using a cable connected to SWD connector CN4

2023年2月8日 · This article tells how to program/debug a STM32 MCU in an external application board with ST-LINK/V2-1 on Nucleo-64 development board (e.g.NUCLEO-F411RE programming Blue Pill-STM32F103C8T6 by 4pin-Jumper Wire)

There are two different ways to program and debug the onboard STM32 MCU: • Using the embedded STLINK-V2EC • Using an external debug tool connected to the STDC14/MIPI10 connector (CN4) Refer to Table 10 to switch between STLINK-V2EC and STDC14 configurations. The STLINK-V2EC facility for debugging and flashing is integrated into the STM32 ...