2018年1月31日 · i flew today at a horse farm with the x5s + 14-42 mm and the DJI weight ring and it looked shaky when operating the camera (left, right, etc.) but stable when the m210 just flying. looked shaky on the CS, didnt give me confidence that it was going to be a smooth footage.

2018年2月16日 · Can anyone that owns an M210-RTK provide the basic exterior dimensions (L x W x H) of the DJI OEM case that it comes in? I have also seen pictures of different versions of the M200series case, one with a zipper similar to the Inspire case and one that has latches. I assume the zippered one is for the base M200 and the one with the latches is for the M210 and M210-RTK, is that correct? If ...

2024年6月30日 · DroneTechNZ Posted at 2019-9-10 01:44 Hi. Today we have spent countless hours trying to solve this problem. I have searched far and wide and finally found this document from DJI.

2017年10月17日 · My DJI M210 RTK came shipped witht the Dual Gimbal attached. I am attempting to remove the dual Gimbal and install the single Gimbal. After watching all the video on how to install the dual Gimbal BACKWARDS, I am stumped. The two forward most hole that should recieve the rummer damper that attaches the downward Gimbal appear to be too small to pul the rubber piece below. Please check the vidoe ...

2017年12月19日 · Dear all, I reckon this may have been asked before, but I couldn't find any direct reference to this question. So here goes. How does one go about to extract the RTK-GPS data that is (supposedly) stored on the M210-RTK's flight controller? Each image is obviously provided with reference data in the EXIF file, but I'm quiet sure this is provided by the default GPS unit inside the aircraft. I ...

2020年2月11日 · We have a M210 RTK V2 and it cannot connecto to PC. It was updating by DJI app method, but in the stage 3 of the updating it froze and could not complete de update. After that the cencende remote controller cannot link to the aircraft. Everytime we plug it, windows recognize a new device and 5 seconds after is connected it disconnected by itself.

2017年11月15日 · I ordered a M210 back in September, choosing it since it was one of few drones I could find with an upward gimbal. Well, so far it was in my hands for two days, it did not work when we first unboxed, had several firmware issues, didn't want to connect to the X5s we purchased along with it. We did all the necessary updates, and tried to change to the single downward gimbal. First off, this is ...

2019年7月2日 · 2.Can I switch the dual downward gimbal connector on the M210 V2/M210 RTK V2 to a single downward gimbal connector?No. The gimbals are the same used in M210 v2 and v1? I'm unable to find the gilbals page in dji. The gimbals …

2018年1月27日 · I am using a new XT (V2) on my M210. When I check the XT firmware version on the Go app or Pilot app it says XT Firmware version 01.15.00.59. I downloaded the latest M200 XT Firmware (01.30.0.10) and put in on the XT SD card. When I power on the M210 it powers on normaly and does not update the XT and the app still shows the XT Firmware as 01.15.00.59. Am I updating the XT wrong on the M210 ...

2019年8月2日 · Hi everybody, I have also run into the now known issue with the Zenmuse XT and XT2 cameras. Unfortunately my XT2 does not show any live picture when attached to the Matrice 210 drone. I have control over the gimbal and can see a temperature data on the black screen, but unable to achieve a proper live picture. I also detected that the XT2 now requires two SD cards to be inserted in the two SD ...