These are the basic DT400 and DT402 series throttle operating instructions designed to get you “up and running” quickly and to minimize your “frustration level” as you learn to use the throttle. Turning Track Status On and Off To run your layout you must be sure track power and track status are both ON.

PR3 / PR4 Windows XP Driver Installation. Sept. 11, 2013. Version: 1.0

PX108-6 - Power Xtender For use with Digitrax Decoders Equipped with 6 pin Sound Harness. Instruction Sheet

2022年7月28日 · Here we are getting started with HO Scale all over again! Finally able to clear some room and start work on my dream layout! It may be small, but its a layout none the less. I'm going to record and...

View and Download Digitrax DS44 installation instructions online. Stationary Decoder for use with 4 slow motion turnout machines. DS44 media converter pdf manual download.

View and Download Digitrax ZEPHYR express DCS52 manual online. Digitrax Complete Train Control Starter Set, All In One Command Station Booster Throttle, Power Supply. ZEPHYR express DCS52 control systems pdf manual download. Also for: Zephyr express ps314.

To connect your computer to a Digitrax DCC system, you need either a USB-equipped Command station (DCS240 or DCS52), or a computer-to-LocoNet adapter device such as a LocoBuffer-NG, PR3, PR4, LocoBuffer-II, LocoBuffer or MS100. The LocoBuffer-NG is a highly recommended computer-to-LocoNet adapter. See below for more on adapters.

Page 1 Using Digitrax SoundLoader software with your PC and the Digitrax PR3 Xtra Programmer you can create, manage, test, and download Digitrax sound projects (.spj) in your SoundFX decoders.

See the Digitrax PR3 Windows Setup page for more information. Make sure to follow the instructions exactly, particularly about the order of installing the drivers and plugging in the device. See also PR3 Firmware issue which affects computers running Microsoft Windows below.

How To Set Up Routes Using Your DS64NOTE: During this procedure the DS64 must be connected to an active LocoNet with an active command station.1. Press and hold down the STAT button on your DS64 until the green LED begins to …

To set up JMRI to use the PR4 to connect to a Standalone LocoNet: Start the program. Open the Preferences window from the Edit menu and configure the connection by:

2010年1月12日 · The safest way to wire the programming track is through a DPDT center-off toggle switch. Wire the toggle switch center terminals to the programming track. One set of end connections on the toggle go to the programming track output on the DCC system and the other connections go to the track output on the command station.

Adding an interface for the computer will make a complete programming setup. PR3 and PR4 by Digitrax. Devices such as the PR3 / PR4 from Digitrax can be used, except they lack the ability to operate a vehicle.

SETTING THE NEW 4-DIGIT ADDRESS (RANGE 128-9983) 1) Place the locomotive on your "program" track connected to the "PROG A" and "PROG B" outputs on the back of the DCS52. This has to be a SEPARATE track from your "main" track. They cannot be connected together or damage to your DCS52 may occur!

2017年11月29日 · Check below to see if any firmware updates are available for download for your Digitrax equipment. In addition throttle hardware conversions are available if you want to convert from walk around operation to wireless.

2018年7月8日 · The following are a few helpful tips that I found when I set up my Digitrax system to operate the ProtoThrottle. The first step is to properly set up the LNWI with your Digitrax system. This is a relatively straight forward installation with connecting a Loconet cable from the LNWI to your Digitrax Loconet system connection.

2014年12月18日 · It can also be set up as a 3.0 amp booster if you upgrade systems. The Zephyr Xtra is the only system that has 2 novel JUMP ports which allow a DC power pack to run DCC equipped locomotives. One of the local clubs has obtained a Zephyr Xtra to determine if their existing DC layout wiring will work with DCC.

2011年11月4日 · This program allows convenient Duplex Group setup for any UR92 on LocoNet.

With Digitrax LocoMotion, there are two types of speed tables: 3 Step Tables and High Resolution 28 Step Tables. Please see your Decoder Manual for a discussion of the 28 Step Tables. The 3 Step Tables are set up by programming 3 CVs: Start Voltage (CV02), Mid point Voltage (CV06) and Max Voltage (CV05). These values are set at 000 at the factory.

Everything you need to get started with Advanced Digitrax Command Control. Evolution Express is perfect for most home and club layouts. It offers excellent speed control, prototypical consisting, the full range of programming features and much more.