HS-6 powder question - Ruger Forum
2011年8月28日 · Lefty, HS-6 is a medium slow burning powder and is not a general purpose powder like Unique or AA#5. It is not considered a "do not reduce" powder like you see with H-110, however it burns much better when pressure is higher. There are three reasons for NOT reducing charges below the minimums listed in reloading manuals.
Hs-6 for 45 Colt - Ruger Forum
2020年3月14日 · HS-6 likes more of a full power load, it does not do well with light charges. When I was working up the load, my beginning charges were erratic velocity and lots of unburnt powder. Once I was above 10.5 grains, it settled down to low deviation between shots.
HS-6 powder - Ruger Forum
2015年7月15日 · Hodgdon list 11.7 grs. ~ 13.0 grs HS-6 with a 200 gr. bullet. (I'm assuming .45 Colt) Set your sights on pistol reloading data | Hodgdon Reloading I have found HS-6 to be about the most versatile powder for larger caliber loads, from light target loads to moderately heavy. Replaced old Winchester 540. Bob Wright
HS-6 and the 357 - Ruger Forum
2011年2月25日 · You NEED to get some HS-6, MidLife. It's a super powder, IMHO and great for the 38/357 clan as well as 45 Auto. One load I took today that's worthy of mention is 4.5 gr of 231. Gary turned me on to this powder in another thread and I decided to try it-glad I did.
Problem in 45 ACP handguns using Hodgon HS 6 powder
2014年7月27日 · Found some HS-6 at a local store (pistol powder of any type/brand is scarce in my area). Am loading 200 gr. Berrys plated truncated cone flat nose style bullets .452 in. diam. , and using a charge of 8.5 grs. HS-6, and a CCI 300 standard large pistol primer. After a few mags. of these loads are run through either of my two pistols.
.38 special and HS-6 - Ruger Forum
2011年9月15日 · Today, I shot my two revolvers, (Ruger SP 101 and S&W 66 with a 4 inch barrel) using 6.6 grains HS-6 and there was unburned powder on the shooting table afterwards. For some reason I wasn't getting a complete ignition of the powder in my 38 special loads. I used CCI small piston primers and 125 grain Berry's FP bullets.
HS-6 for .44mag Snubby Loads - Ruger Forum
2017年3月15日 · One of the things that I read about HS-6 is the guys running compensated match guns get good amounts of gas to dampen recoil in .38 Super and 9mm Major. Thought it might help since my Alaskan is ported. I also read that magnum primers should be used for better ignition and cleaner burning especially in large capacity cases.
Cleaning up 38 Special HS-6 loads - Ruger Forum
2016年11月7日 · With a 158 grain lead bullet in .38 Special, I have used 7.0 grains of HS-6 for a practice load. "Serious" loads are a bit stronger than that... in my guns. 2. Non-magnum primer. HS-6 requires a magnum primer for a clean burn. This is a long-known fact with HS-6, which most current manuals disregard for sake of - laziness.
No Data with HS-6 for 44 Mag - Ruger Forum
2011年5月6日 · HS-6 is a mid-burn rate powder so it will generate higher pressure than one might think but 21.8k is still only 60% of a max pressure load. The formula is: BHN=chamber pressure divided by 1400. bwelch47, Yes, flying ash cans have the aerodynamics of …
Hodgdon cfe pistol powder - Ruger Forum
2018年8月25日 · CFE-P is right in there with Ramshot Silhouette, HS-6, and Win AutoComp. I obtained a few pounds of CFE-P for working on moderate .357 and .44 Mag loads, as well as trying it for max 9mm loads with 115-125 gr bullets. I am nearly out of Accurate #7, which has proven to be an excellent 9mm powder for max loadings, as well as moderate .44 Mag loads.