2005年1月12日 · To display the IP ARP table, use the show ip arp command in Privileged EXEC Mode.

2024年7月8日 · 在使用 uboot 的网络功能之前先用网线将开发板的 ENET2 接口和电脑或者路由器连接起来， I.MX6U-ALPHA 开发板有两个网口： ENET1 和 ENET2，一定要连接 ENET2，不能连接错。 2. 将开发板和主机连接在同一个路由器或者网域内， 使用SD卡移植uboot，启动uboot,在 MobaXterm 软件 终端窗口可以看到启动过程；可以看到开发板的网络功能还没设置，开发板的MAC地址ethaddr没设置； 点击reset按钮重启uboot发现，因为此时已经有开发板的物理地 …

2010年4月23日 · arp retry count exceeded是指ARP请求重试次数超过了设定的阈值，通常是因为网络中存在ARP欺骗或者ARP缓存污染等问题导致的。而star则没有明确的上下文，无法确定具体含义。

2022年3月30日 · Just connect the USB device connector to a PC and install the RNDIS driver as described in the installation section of https://www.utasker.com/docs/uTasker/uTaskerRNDIS.pdf (assuming you are on Windows). This allows any USB processor to function as a network to a PC without needing it to do a USB-Ethernet adapter function.

2024年4月20日 · 该文指导如何将IMX6ULL开发板与Ubuntu主机设置在同一网段并实现通信，包括在U-Boot中配置IP，使用TFTP服务传输内核与设备树，以及通过NFS挂载根文件系统。 详细步骤涉及设置环境变量，安装TFTP和NFS服务器，以及调整bootargs以启动内核。 首先根据这篇博客，保证自己的开发板与Ubuntu主机处于同一个网段，并且可以ping通. 【IMX6ULL驱动开发学习】03.设置IMX6ULL开发板与虚拟机在同一网段. 1. 在uboot中设置网络. 首先启动自己的板子进 …

ARP (Address Resolution Protocol). The ARP is a communication protocol used for discovering the link layer address, such as a MAC address, associated with a given Internet layer address, typically an IPv4 address.

* * If the requesting IP is not on our subnet, wait 5ms to * reply to ARP request so that our reply will overwrite * the arp-proxy's instead of the other way around. */ if ( (NetReadIP (&arp->ar_tpa) & NetOurSubnetMask) != (NetReadIP (&arp->ar_spa) & NetOurSubnetMask)) udelay (5000); #endif NetSendPacket ( (uchar *)et, eth_...

The IMXRT1052QSPI device is produced by NXP and is part of the iMX device family. The device supports 6 hardware breakpoints. PEmicro provides various tools which work with the IMXRT1052QSPI, many of which are free.

Enter a static entry in the ARP cache for the specified L3 Pseudo wire interface identifier. This is a unique value that represents the specific interface. This value ranges from 1 to 65535 for Pseudowire interface.

2017年2月15日 · In my setup, I have an IMX6, connected through RMII to a Marvell switch (88E6071 / 100Mbit). For the phy-bus, I make use of the fixed-phy/fixed-link driver. My kernel is linux 4.1.36.xxx. I already had 2 setups, one where The IMX6 washgenerating the ENET_REFCLOCK, and one where I let the marvell do it. Both …