2021年7月19日 · ITO-PEDOT:PSS/P3HT:PC 60 BM/Al OSC is designed and optimized. The parameters of fabrication are optimized; post-production annealing temperature, P3HT:PC 60 BM thickness, and cathode composition (Mg-Al). The HTL, PEDOT:PSS, was prepared under optimized conditions; 3000 rpm for 35 s and annealing temperature of 178 °C for 15 min.

2021年1月1日 · In this paper, we have carried out numerical analysis (modeling and simulation) on current (I)-voltage (V) characteristics of both pristine P3HT and P3HT: PCBM blend both under equilibrium and non-equilibrium conditions.

Our study shows the characteristic periodicity of the regioregular P3HT identified in the nanoscale domain areas with submolecular resolution. Such areas are then distorted in place when adding different quantities of PCBM forming stoichiometric mixtures.

2020年7月1日 · Conventional and Inverted P3HT:PCBM Organic Solar Cells are numerically compared. Different active layer, ETL and HTL materials and multi-thin layer electrodes are studied. The best OSC efficiency is for the Al/TiOx/P3HT:PCBM/ZTZ structure. For IOSC the best structure is Ag/PEDOT:PSS/P3HT:PCBM/ATZ.

2023年6月1日 · In this study, we designed a highly efficient ITO/PEDOT:PSS/P3HT:PCBM/Al-based bulk heterojunction organic solar cell. We investigated the performance of various optical and electrical properties of the designed organic solar cells.

2023年1月6日 · The performance of the inverted P3HT: PCBM-based organic solar cell with device structures of ITO/ZnO/P3HT: PCBM/MoO 3 /Ag was successfully studied via simulation using the GPVDM software. The investigation results showed that thickness of active layer, hole transport layer, and electron mobility plays a vital role in boosting the performance ...

本工作采用具有良好疏水性的聚 (3-己基噻吩-2,5-二基) (P3HT)对PEDOT:PSS进行表面修饰，降低其吸水率，从而提高PSC的效率和稳定性。 结果表明，掺入 P3HT 有效增强了 PEDOT:PSS 的疏水性。 此外，它还促进了 PEDOT:PSS/P3HT 双层上大晶粒钙钛矿薄膜的发展。 这一增强使 PSC 的功率转换效率 (PCE) 达到 19.78%，比参考电池（PCE 的 17.04%）提高了 16%。 经过 1000 小时的持续时间后，用 P3HT 修饰的器件的 PCE 保持在 90% 以上，而参考器件的 PCE 低于 …

2023年6月5日 · It was found that the mass ratio of donor (P3HT)/acceptor (PCBM) = 1:1 in the active layer, with chlorobenzene as a solvent, an ITO anode, PEDOT:PSS as hole transport layer, ZnO nanoparticles as electron transport layer, and sputtered Ag cathode were the most appropriate circumstances for fabrication of cheap and simple flexible SCs.

Three PbS/CdS quantum dots sensitized ZnO nano rods array solar cells with ITO coated down converting glass as a substrate have been fabricated by changing 10, 15 and 20 SILAR cycles for PbS/CdS...

1 天前 · The dissociated holes may be easily transported to the MoO3/Ag anode via the networks of NiO and CuO, whereas electrons can be extracted from P3HT via PC61BM to ZnO/ITO. In other words, infiltration of NiO/CuO into the blend allows P3HT to stack and provides percolated pathways for hole migration to the MoO3/Ag contact [48, 49]. Moreover, the ...