318 Stroker Build - For A Bodies Only Mopar Forum
2018年7月1日 · Yes, if your pistons are set up for your stroke. Your stroker pistons will be shorter to handle the increased stroke of the 4.00 crank so pistons are going to be "stroker pistons". Your stock 318 cam will not get you 300 with only 80 more cubes. Look at the stock Mopar 400 for CID comparison, 190 HP!
Anyone done the 318 to 390 stroker build - For A Bodies Only …
2008年1月9日 · I need more power ! Currently running a 318, .030 over, 340 cam, edelbrock performer intake 600cfm elelbrock carb, early 340 exhaust manifolds. Runs good but I want more... Thinking of doing the 390 stroker, just wondering if anyone has done it,, did you buy a kit or shop for the parts...
318 stroker builds - For A Bodies Only Mopar Forum
2015年3月4日 · I want to fly the MOPAR banner to it's potential without fear of grenading the original motor. Now, I have a virgin bore "72 318, and an extra set of 915 "Z" heads. ( 202/1.6).I want to make a stroker I can hammer on the street. I've been looking at Campbell Enterprises stroker kit. I'll run either a Crane Cams or Comp Cams Hydraulic roller cam ...
318 LA 4inch stroker pistons | For A Bodies Only Mopar Forum
2021年12月7日 · So I already have a 318ci block at 4 inches, that had an ‘old school’ 360 stroker kit in... Seeing the 340 stroker cranks are a good buy @ £400 just need to find some 4 inch bore pistons... Should have said they was going to race Darts me thinks, bit risky saying Coronet on an A-bod site, oops...
318 stroker using Scat crank | For A Bodies Only Mopar Forum
2014年5月9日 · My 318 stroker build would consist of this Scat crank, plus KB flat cast pistons with 1.658 CH, shaved down to 1.640 . This would also place these low surface-to-volume flat piston down in the bore about 0.40 , and still net me about 9.7:1 CR (66cc chamber).
318 to 390 stroker - For A Bodies Only Mopar Forum
2020年1月16日 · I have also started thinking of a 318 magnum stroker, I have a new 4 inch stroker crank that I was going to use in a 340 but ended up staying with a stock stroke for that build. I was thinking that a 318 magnum block is at least $500 cheaper than a 340 block...plus the 318 magnum is a roller cam block
318 Poly Stroker Crank & Rods - For A Bodies Only Mopar Forum
2021年6月16日 · Years ago I thought about doing something like this with an LA 318; 360 crank in a 318; I had a set of Badger cast, pin height 1.74 inches, doing the math, the piston stuck out of the bore .055, fly cut them to zero deck, then figure valve reliefs, I was getting the notion that the crown might be getting a little thin, I scraped the idea.
318 Stroker - For A Bodies Only Mopar Forum
2016年6月17日 · Hughes , eagle, and others do however make cast and forged stroker cranks to bump up the displacement of the 318. Most 318s cannot take a 4.000 inch bore however making the 340 block pretty prized. The smaller bores on the 318 make valve shrouding a problem if running 2.02" - 1.60" valves.
Let's talk 318/349/390 strokers. - For A Bodies Only Mopar Forum
A 318/349 build with the 360 crank turned down , factory ported 360 heads and a Comp 282S retro cam (.495 [email protected]), and A 4" 318 / 392 with the same heads and an XS282S cam (.520/.540 - 245/252) There is absolutely no comparison in the torque produced and the ease of build.....go the 392. 349 issues as stated: 1 - Very limited off the ...
318 to 390 hp? - For A Bodies Only Mopar Forum
2010年4月12日 · Got one that has a Mopar Performance crank, Eagle Sir Rods, Diamond Forged Pistons, Comp XE274H camshaft, and Indy/RHS X Heads with 1.92' Intakes. Running about 10.0 compression. Have not had it on a dyno but will need to get to a chassis dyno to get some tuning done; so one day I will find out if it is a stout as it feels.