2021年11月15日 · In the ST-Link V3 datasheet the pinout of the STDC14 connector is mentioned as follows: I have a question regarding: Pin 3: Should I connect the 3.3V signal from the target power supply? As far as I know, this is not for powering, but rather for setting the correct reference voltage, therefore connecting it is important;

2023年1月9日 · Hi, I'm making a board on which I want to use the STDC14 connector of the STlink V3 programmer for the SWO interface of my MCU. But I have some questions about the pinout, in the manual I find this table: 1 - PIN 3 (T_VCC): this pin must be connected to the power supply of my board or is it a power ...

2020年10月22日 · If you don't need the virtual COM port on the STDC14 connector, I would recommend just using the standard ARM 10-pin connector. Fitting the 14-pin connector prevents you from using 10-pin cables. If you use the 10-pin Samtec header FTSH-105-01-L-DV-K-A-TR, you can still plug in the 14-pin cable from the ST Link and use it no problem but also ...

2021年4月15日 · 文章浏览阅读3.8k次。本文介绍了stlink-v3mini的实物图和硬件信息，重点阐述了stdc14接口与jtag接口的对应关系，指出stdc14 pin13/14可用于虚拟串口，可替代rs232和ft232转换工具。

– Flat cables STDC14 to MIPI10 / STDC14 / MIPI20 (connectors with 1.27 mm pitch) – JTAG communication support – SWD and serial wire viewer (SWV) communication support • SWIM-specific features (only available with adapter board MB1440): – 1.65 V to 5.5 V application voltage support – SWIM header (2.54 mm pitch)

STDC14 connectivity with an included STDC14 to STDC14 flat cable. Pictures are not contractual. Figure 1. STLINK-V3MODS product top view Figure 2. STLINK-V3MINI product top view www.st.com. Contents UM2502 ... 6.1.2 32-pin edge connector for STLINK-V3MODS (STM32 JTAG/SWD, VCP

2022年8月31日 · Professilnal debug probe like I Jet or J Link use this type of connector 10 or 20 pin version. For the edge connector it is a Kyocera AVX10 board to board connector, with 2mm pitch, I guess dual row header with or without right angle can easily be soldered, or maybe the DF11-10DP to make cables. 0 Kudos Reply. Imen.D.

The STDC14 Adapter adapts from the 20-pin 0.1'' J-Link and Flasher debug connector to the 14-pin 0.05'' connector defined by ST. STDC14 Adapter. STDC14 Adapter Pinout. Headquarters SEGGER Microcontroller GmbH. Ecolab-Allee 5 40789 Monheim am Rhein, Germany [email protected] Tel.: +49-2173-99312-0 ...

This cable connects ST programmers and debuggers such as STLink-V3 and STLink-V3Mini that have a 14-pin 50mil FTSH style header that ST call STDC14. This extends the typical 10-pin Cortex connector by adding a serial port and other reserved signals.

2023年9月12日 · 这是一个 STLINK-V3 STDC14座转2.54mm排针转接板Kicad工程 。STDC14座实际工作中不太方便，所以搞了这个转接板。另外转接版上提供了可选的电源输出功能。 An adapter board for STLINK-V3. It change the STDC14 to 2.54mm pin header.It also provides 5V and 3.3V power supply through an additional USB interface.