TMC ‘extruder’ reports error: DRV_STATUS: 601f1000 s2vsa=1(ShortToSupply_A!) csactual=31 ola=1(OpenLoad_A!) olb=1(OpenLoad_B!)） . 报错详情. 暂无图片; 报错原因. 检查驱动器电流不正确; 主要解决方法. 检查步进电机AB两组线圈阻值是否一致; 检查步进电机或者部件电机内部的电线 …

2021年7月7日 · Update: now my extruder makes a buzzing/clicking noise (not the type you get from skipping stepps) when trying to move. What is going on?! restarting klipper fixed this …

2021年7月9日 · The root cause of your issue is a “TMC reports error” problem - the cause and common fixes are documented at: https://www.klipper3d.org/TMC_Drivers.html#why-did-i-get-a-tmc-reports-error–error. You may also wish to try completely disabling stealthchop mode as that can often cause subtle issues like this.

2023年10月17日 · TMC ‘extruder’ reports error: DRV_STATUS: 601f1000 s2vsa=1 (ShortToSupply_A!) csactual=31 ola=1 (OpenLoad_A!) olb=1 (OpenLoad_B!) I’ve checked this page where it said it could be the wiring, stepper driver, or extruder and so I’ve done the following, but still get the same error every time.

2023年4月28日 · From what I can tell from the "TMC2209 Datasheet" s2vsb=1(ShortToSupply_B!) indicates low side short phase B and ola/olb indicates a open load phase A/B but that could be a false detection. I pulled the driver from the board to check connection but that seems good.

2022年8月17日 · Right after fixing my previous issue, I ran into the next. For any axis I try to move, buzz or home I get error (s). The stepper very shortly does get power (like, half a second), and then right away klipper shuts down the MCU. Last time I just had some lines wrong, I hope its the same case this time.. Things that may perhaps be of use:

TMC ‘extruder’ reports error: DRV_STATUS: 601f1000 s2vsa=1(ShortToSupply_A!) csactual=31 ola=1(OpenLoad_A!) olb=1(OpenLoad_B!) . Error Details. No image available; Error Cause. Incorrect driver current check; Main Solution Method. Check if the resistance values of the two coil groups A and B of the stepper motor are consistent

2022年11月14日 · 本文写关于VORON2 的接线详细以及注意事项。 连接打印机电子设备时，您将使用电压220V/120V的交流电接线，请在触摸任何电线或端子之前，务必仔细检查以确保您的打印机已拔下电源，并且确保电路或器件中的电容器已放电完全（例如，如果没有负载的话，需要等待1分钟以上，可以观察开关电源的绿色工作灯是否熄灭，前提是开关电源有这个灯，一般都会有）。 此处提出的建议通常是出于防止火灾的充分谨慎。 接线的时候，要搞清楚正负极的概念 …

TMC驱动程序的 interpolate 设置可以减少打印机运动的噪音，但代价是引入一个小的系统位置误差。这个系统性的位置误差是由驱动器在执行Klipper发送的 "步骤 "时的延迟造成的。

2021年3月13日 · TMC 'extruder' reports error: DRV_STATUS: c00e0090 s2vsa=1(LowSideShort_A!) olb=1(OpenLoad_B!) CS_ACTUAL=14 stealth=1 stst=1 Once the underlying issue is corrected, use the "FIRMWARE_RESTART" command to reset the firmware, reload the config, and restart the host software.