SIP LOOP 480 temporarily not available - Cisco Community
2015年1月26日 · I have a CUCM 8.6.2. I use a SIP trunk to make calls but i have a loop that i cant know how to avoid it. 172.23.132.18 is the CUCM. 172.23.129.35 internal SBC 172.23.129.48 external SBC 172.23.254.245 Alcatel OXE. I want to know how can tell CUCM to stop when a 480 is received. Thank you so...
SIP: No matching Codecs / 480 Temporarily not available
2015年10月14日 · The problem persists after I tested multiple Codec Settings - seems like the codec isn't at fault. I think the third phone malfunctions because currently it's only in a test set-up without actual SIP Provider, just an elmeg 130j PBX.
SIP troubleshooting - incoming and outgoing call failed (SIP/2.0 …
2016年6月10日 · Does your SIP trunk has calling search space set for incoming calls I believe you are trying to call 581 extension on CUCM , please make sure trunk has access to that . Also if you are maniplutaing any digits using transklation pattern etc before sending calls to ext , trunk should have access to that.
Solved: Outbound Call Failure - SIP Trunk - Cisco Community
2013年12月18日 · All phones are unable to dial a single target number on the PSTN. The symptom is that it rings once and goes fast busy. The call flow is: Phone >>> CUCM >>> CUBE >>> Verizon SIP Trunk >>> PSTN >>> Target Number As seen in the CUBE debug ccsip messages, the CUBE receives a "SIP/2.0 480 Temporarily...
Temporarily Not Available for a Forwarded Call Over SIP Trunk
2016年9月24日 · I have a SIP trunk from my Service Provider (STC- Saudi Arabia). ITSP<----->CUBE<----->SIP<----->CUCM Cluster. I have some problem during the call forward. Some calls are being forwarded without any issue: 1) A call from internal extension to another internal extension forwarded (say call forward no answer)successfully to the PSTN.
SIP Trunk /// SIP/2.0 480 No Routes Found - Cisco Community
2012年5月15日 · I trying to make outbound calls to a sip trunk but when i dial a receive an fast busy tone, in debug ccsip messages i receive this disconnect cause: SIP/2.0 480 No Routes Found. Follow attached the output of the debug. I already have configured the Route Groups - Route List and Route Patterns and the dial-peers on the gayeway. Inbound calls are ...
SIP/2.0 480 No Routes Found error - Cisco Community
2008年11月17日 · Hi, I've a CCME 4.x with SCCP phones. Now I need to reach the PSTN via SIP. So I've set-up a VOIP dial-peer but it doesn't work. I've enabled all SIP logging and I've read this error: SIP/2.0 480 No Routes Found and then Number of Media Streams: 1 Media Stream : 1 Negotiated Codec : No Codec Negot...
Disconnect Cause SIP 480 Outbound Calls through E1 PRI
2016年10月18日 · Hello All, I'm getting erro : SIP 480 , when I try to call to PSTN through E1 PRI connection. Any suggestions? the carrier says : I'm OK , they tested directly in their equipment and the call was ok. Pls help ! :( Logs look : The Call Setup Information is: Call Control Block (CCB) : 0x0x22A55F...
CUCM not sending ACK for an outgoing INVITE - Cisco Community
2015年8月11日 · The SIP 480 Temporarily unavailable indicates that the callee was contacted but is temporarily unavailable. You can collect the CCM trace from RTMT to start with. RTMT->Trace & Log Central->collect files->Select Cisco Call manager and collect the traces. -Venkatesh
基本的な SIP コール フローとトラブルシューティング コマンド …
2014年7月2日 · このドキュメントは英語版の日本語訳です。最新の内容は英語版をご参照ください。 はじめに このドキュメントでは、PBX、ゲートウェイ、および SIP 電話機間の基本的なSIP コールフローについて詳しく説明します。このドキュメントの目的は、初心者がさまざまな SIP コール フローと ...