Apr 20, 2024 · Pin 5 is either an enable control input (EN), a VIO supply pin or is not connected. Pin VIO on the TJA1051T/3 and TJA1051TK/3 should be connected to the microcontroller supply voltage (see Figure 6)

Feb 28, 2020 · To switch the device in normal operating mode, set the STBY pin to low and the TXD pin to high (see Table 1-1 and Figure 1-2). The STBY pin provides a pull-up resistor to VIO, thus ensuring a defined level if the pin is open. A low level on the NSIL pin (available on pin 5) and on the STBY pin selects Silent mode.

Aug 4, 2023 · 1、vio引脚：can收发器配有专用的vio引脚，rx、tx可以直接与电源电压为3.3v和5v的微控制器对接。 VIO和非VIO版本采用相同的封装供应。

第1步：在vivado中，打开IP核目录（IP Catalog），在搜索框中输入ILA（不区分大小写），按图示方式进行选择即可。 第2步：设置ILA参数. 第3步:测量信号的位宽进行设置： 第4步:在IP source区，打开ILA，添加例化模板, 在代码中插入例化，把 VIO 的输出口连接到模块的输入。 .clk(clk), .probe0(probe0), .probe1(probe1), .probe2(probe2) VIO的输出可以控制测试模块的输入，VIO的输入可以显示模块的输出值。 第1步: 例化一个VIO核，根据需要设定输入输出的数目. …

Variants with a VIO pin allow for direct interfacing with 3.3 V to 5 V microcontrollers. Variants without a VIO pin can interface with 3.3 V (except TJA1044C) and 5 V-supplied microcontrollers, provided the microcontroller I/Os are 5 V tolerant.

1.4 Supply Pin for I/O Level Adapter (VIO) This is the supply pin for the digital input/outputs pins. This pin should be connected to the microcontroller’s supply voltage to adjust the signal levels of pins TXD, RXD, NSTBY, EN and NERR to the I/O levels of the microcontroller. The VIO pin is monitored for undervoltage conditions.

Learn the advantages of a narrow filter time according to the new ISO specifications as well as the benefit of the VIO pin; Be familiar with Infineon’s TLE9252VSK and TLE9252VLC transceivers and their unique selling points

The TJA1042 offers improved electromagnetic compatibility (EMC) and electrostatic discharge (ESD) performance, it features ideal passive behavior to the CAN bus when the supply voltage is off, a very low-current Standby mode with bus wake-up capability, and variants with a VIO pin can be interfaced directly with microcontrollers with supply ...

• The TJA1462A is a high-speed CAN transceiver with Normal and Standby modes and a VIO supply pin. The VIO pin allows for direct interfacing with 3.3 V- and 5 V-supplied microcontrollers.

Jan 10, 2022 · using only the VIO pin. This allows VCC to be removed reducing power consumption further。 你看这个9.4.3描述。 他是 the bus lines are biased to ground被拉到地了，而且你看你F9.2，描述的STB条件下，内部是拉到地的。 那跟这个描述有区别啊，而且如果偏置到VCC/2。 你手册里面的STB功耗也 不满足啊。 您的理解是对的，在standy mode ，总线是以上图B连接，而其他正常模式收发器则试图将CAN总线保持在2.5V。 因此，会产生一条泄漏路 …